To stop paperback covers from curling, store your books in stable, dry conditions, support their covers during storage and transport, and gently flatten minor curls under an evenly distributed weight. Avoid heat, added moisture and forceful bending. These can damage the coating, crease the card or weaken the binding, and you may not be able to flatten every curl completely.
Why do paperback covers curl?
A paperback cover usually combines paper or card with printed ink and sometimes a plastic coating. These layers respond differently to moisture, so one side can expand or contract more than the other, making the cover bend. You may find a curl even in an unread book; it doesn't necessarily mean someone stored it carelessly.
Repeated changes in humidity can make the problem worse. You can also leave a lasting bend if you fold a cover behind the book, leave it hanging over a shelf edge or squeeze it into a crowded bag. Thin covers resist these stresses less well than heavier card.
Look closely before you try to flatten the cover. You're more likely to improve a smooth, gradual curve with gentle pressure than a sharp crease. If you see bubbling, peeling film or layers separating at an edge, the cover has damage that pressure alone won't repair.
How to flatten a curled paperback cover
If you have a dry, ordinary reading copy with a mild curl, try gentle, even pressure. Work on a clean, flat surface, and check for grit on the book or underneath it that could leave an indentation.
- Check that the book is completely dry. Don't use this method to press a damp book.
- Close the book with all pages lying naturally inside the covers. Ease the curled cover towards its normal position without forcing it or folding it backwards.
- Place the book between two smooth, clean, rigid boards slightly larger than the book. Put plain, unprinted paper between the boards and covers to protect against scuffing.
- Place a modest, stable weight on the upper board. Centre it to spread the pressure across the cover rather than concentrating it at an edge.
- Check after several hours. If nothing has creased, shifted or stuck, leave it overnight and inspect it again.
There's no fixed pressing time that works for every paperback. You may see a slight curl improve overnight; a more persistent bend may need several days of gentle pressure, with daily checks. Don't keep adding weight if the cover resists or the spine starts to distort.
Once you remove the weight, watch for the curl returning. If the cover flattens temporarily but then curls again, the storage conditions or its layered construction may still be causing the problem. Repeated pressing won't necessarily give you a permanent result.
How to store paperbacks to prevent curling
Choose a shelf away from direct sunlight, heaters, damp walls and sources of water. The Library of Congress recommends a cool, relatively dry, stable environment for books, with minimal exposure to light. You'll generally find it more practical to avoid repeated changes in these conditions than to maintain an exact humidity level.
Give each paperback support without squeezing. Stand books of similar sizes upright together, using a smooth bookend where needed to stop them leaning. Leave enough room to remove a book without dragging it hard against its neighbours, but not so much that its cover falls open.
If a thin or oversized paperback won't stand upright without bending or leaning, store it flat on a shelf that supports its whole cover. Keep stacks low enough that you can retrieve books without pulling them from beneath a heavy pile. Never let an oversized cover project beyond the shelf.
Check newly acquired used books before shelving them alongside the rest of your collection. If a copy feels damp, smells musty or has suspicious fuzzy patches, keep it separate and investigate before pressing it or putting it in a sleeve or box. When you pack stock in boxes, support the books so they can't slump, and keep the boxes off floors where leaks or cleaning water could reach them.
Do protective sleeves stop paperback covers from curling?
A sleeve can protect your paperback from rubbing and bent corners during transport, but it can't compensate for unstable storage conditions. Choose a loose-fitting, non-adhesive sleeve that lets you insert and remove the book without flexing its cover. Don't seal a damp book inside a sleeve or any other enclosure.
You can give a thin cover extra support with a removable jacket designed for paperbacks. Check that its folds don't pull the front or back cover outwards. If you want to preserve resale or collectible value, avoid attaching adhesive film directly to the original cover.
In a bag, place your book in a separate compartment or between flat items that support its full size. Keep bottles and anything else that might leak separate. While reading, support the open book instead of folding one cover behind the other, and use a bookmark rather than leaving it face-down.
What should you avoid when flattening a paperback cover?
Don't iron the cover, heat it with a hairdryer, spray it with water or wipe it with a damp cloth to soften it. Heat and moisture can affect inks, coatings, adhesives and paper unpredictably. A method that seems to work on one paperback can leave another with ripples, stains or peeling film.
Avoid forceful reverse bending, tight elastic bands and clips. These concentrate pressure and can replace a smooth curl with a permanent crease or indentation. Don't use tape or glue to fix curling either; they change the cover and may complicate later repairs.
If gentle pressing makes little difference, accept a modest curve on an ordinary reading copy rather than risk further damage. Consult a qualified book or paper conservator before treating a signed, scarce or valuable paperback, or one with flaking print, separating layers or a damaged binding. Ask a bookseller experienced in collectible editions about its value before you make any permanent alteration.